Grease Sachets for OEM Kits: Getting the Fill Quantity Right

Learn how to turn an approved lubrication requirement into a grease sachet specification, covering fill weight, usable dose and practical dispensing checks.

Grease Sachets for OEM Kits: Getting the Fill Quantity Right

Specifying grease sachets for an original equipment manufacturer (OEM) kit starts with the lubricant and quantity approved for the job. Before ordering, check that the proposed pack lets the user apply that quantity in practice. The amount filled, the amount recovered from the sachet and the amount reaching the component need to be considered separately.

For a kit assembler or grease supplier, this is a practical packaging question. A pack may fit neatly inside the box yet be difficult to empty or control. Working through the details before production gives everyone a clearer specification to approve.

What does the job require from the grease sachet?

Start with the equipment manufacturer’s lubrication requirement and, where needed, advice from the lubricant supplier. Confirm the exact grease and required quantity for the task. Packaging should support that requirement; a convenient sachet size should not determine how much grease the component receives.

Give the packer the manufacturer’s product name and code, together with the current technical data sheet and safety data sheet where applicable. Descriptions such as “EP2 grease” or “silicone grease” are not enough to identify a particular formulation. State who supplies the product and who is responsible for approving it for the intended use.

An NLGI consistency grade is only part of the product description. As NLGI’s technical guidance explains, it describes consistency rather than the complete formulation. It does not establish suitability for your application. Base oil viscosity and grease consistency are also different properties, so avoid treating either as a complete filling specification.

Describe the job as well as the product. Is the sachet for one component or several? Will the user squeeze grease directly onto the part or transfer it to an applicator? Include any relevant access restrictions and handling conditions. These details help frame a useful discussion about grease sachet packaging.

How do fill weight and usable dose differ?

The required application quantity is the amount specified for the lubrication task. Net fill is the quantity of grease inside the sealed pack, excluding the packaging itself. The usable quantity is what the user can actually deliver to the intended application using the agreed method. Grease remaining in the sachet, on an applicator or elsewhere during transfer is not grease applied to the component.

Keep the units clear. Grams measure mass and millilitres measure volume; they are not interchangeable. If a requirement is given in grams and a packaging option is described in millilitres, ask for a conversion using the density of the exact product at the relevant conditions. Do not assume that 1 ml of grease weighs 1 g, or convert a published pack capacity into a guaranteed fill weight.

A simple hypothetical example shows why recovery matters. Suppose a sachet contains 10 g of grease, but 9 g is collected after dispensing by a defined method. That demonstrates a difference between the contents and the recovered quantity. It does not show that 9 g is the correct application dose, that the remaining 1 g is acceptable, or that all 9 g will reach the component. These figures are illustrative, not Lubepack test results or filling specifications.

If the user cannot apply the required quantity, investigate the opening, pack shape and application method with the packer. A different format may help, but it still needs checking with the actual grease. Our guide to choosing a packaging format for liquids, greases and pastes explains the broader options.

Do not solve a recovery problem by reducing the approved lubrication quantity or adding an arbitrary percentage to every pack. Any change to the proposed fill should be agreed alongside the application instructions and checked again in use.

How should the pack be tested before approval?

Ask for a trial plan using the intended grease and proposed packaging. Agree the number of samples, test conditions, measurement method and acceptance criteria with the relevant technical teams. Decide who will approve the result before testing begins. A successful demonstration with one pack should not be treated as proof that the production specification is settled.

Use a method that reflects the real task. If the instructions require squeezing the pack onto a component, opening it completely and scraping it clean would answer a different question. Where gloves or an applicator form part of the approved working method, include them in the trial. Check whether the user can open the pack and control the grease without unintended discharge.

Record what is being measured. A before-and-after pack weight can show how much material left the sachet, provided the method accounts for the packaging and any removed pieces. It does not, by itself, show how much reached the component. Identify where residue remains and use an agreed measurement method suited to the question you need to answer.

Review the printed instructions alongside the physical pack. The product identity, opening method and application guidance need to be clear at the point of use. Follow the product’s handling advice; HSE guidance on safety data sheets explains their role in providing hazard, handling and storage information.

Keep immediate usability checks separate from storage approval. A freshly filled sachet that opens well has not demonstrated its shelf life. Ask what compatibility, seal and storage evidence is needed for the particular grease and packaging, including the expected conditions before use. Agree any further testing rather than assuming that the bulk product’s storage guidance answers every question about the finished pack.

What should go into the production specification?

Bring the approved requirements together in a written specification. This gives the grease supplier, filling partner and kit assembler a common reference, and makes it easier to assess a proposed change later. Use the checklist below to prepare the information for discussion; the final requirements need agreement for the individual project.

     
  • Product and task: Exact product name and code, supplier, current data sheets, intended task and technical approver.
  •  
  • Required quantity: Approved application quantity and units, plus the proposed net fill and agreed dispensing method.
  •  
  • Pack and opening: Selected format and dimensions, opening arrangement, application method and fit within the kit.
  •  
  • Trial acceptance: Sample quantity, conditions, measurement method, usable quantity criteria and named approver.
  •  
  • Fill control: Nominal fill, agreed tolerances and verification method, with responsibility for production checks.
  •  
  • Artwork and identification: Product identity, instructions, required warnings and agreed batch or date coding requirements.
  •  
  • Storage and supply: Agreed storage conditions and shelf life evidence, outer packaging, order quantity and delivery requirements.

Keep a record of the approved pack and specification version. If the grease, packaging material, opening or application instructions change, agree whether the earlier trial results still apply. An apparently small alteration may require another check, so identify who must approve changes before they reach production.

At Lubepack, our contract filling and packaging services cover customer-supplied greases and lubricants, with the option to discuss sourcing suitable products through our supply partners. We can also support pack design, artwork and outer packaging. The product, fill quantity and intended use provide the starting point for assessing a suitable packaging option.

To discuss your grease sachet requirements, send us the exact product details, approved application quantity and expected order quantity. Explain how the pack will be used and any constraints within the kit. That gives our team the information needed to discuss the next steps with you.